How To Remove Mortise Lock
Whether you lot want to supercede a lock altogether or y'all need to remove a lock to make a repair, removing a residential door lock is something you can easily do yourself. With the right tools in paw and articulate instructions, removing a door lock is an easy DIY task. Read on to acquire how to remove the knob, cylinder, and mortise locks.
Removing a Knob Door Lock (With or Without Visible Screws)
A knob door lock refers to a door turn-knob that has the lock built right in. Most commonly, these are establish on interior doors within a home.
Sometimes, knob door locks will also be used (along with a deadbolt) for an exterior door, but they are non recommended as the primary lock for any exterior door due to how easily they tin can exist removed or forced.
Tools Needed
To remove your knob door lock, y'all'll need to kickoff past making sure you have the right tools for the job:
- Wire or small nail
- Flat-caput screwdriver
- Phillips-head screwdriver
Removing a Doorknob with Visible Screws
The first stride is determining whether your doorknob has visible screws on the rose plate. If it does have exposed screws, these should be on the interior knob (the 1 you use to lock the door).
Step 1: Remove These Screws
If your doorknob has visible screws, your chore volition be piece of cake. Take hold of the Phillips-head screwdriver and kickoff unscrewing the ii visible screws.
Stride two: Remove the Doorknobs
Once yous've unscrewed those screws, you should be able to simply remove the interior and exterior doorknobs.
Step 3: Unscrew the Face Plate
Pick up the Phillips-head screwdriver once more and start unscrewing the two screws located on the faceplate.
Footstep iv: Remove the Latch
In one case you lot've removed the screws from the faceplate, simply grab the latch and pull the entire thing out.
Removing a Doorknob with No Visible Screws
Can't find any visible screws on your doorknob?
Stride 1: Locate the Slot
All knob locks have what's known as a slot with a latch; this is what holds the knob in place. You can notice the slot on the shank of the inside knob (the ane you use to lock the door). This is usually a modest, rectangular pigsty. If y'all don't run into the hole, try turning the knob to either side until y'all tin locate it.
Footstep ii: Push Button and Remove Knob
Now that yous've located the slot, you'll need a flat-head screwdriver (or a small pin, paper clip, or boom) to press the release push inside of the slot (these tend to be very modest). Push your chosen tool into the pigsty and depress the button. At this point, the interior knob should release from the door easily.
Stride iii: Remove Exterior Rose Plate
Next, you'll need to remove the rose plate. The all-time way to do this is to apply a small, flat-head screwdriver to carefully pry the rose plate away from the door. Commonly, at that place is a modest slot on the rose plate that allows y'all to do this.
Step iv: Remove Interior Rose Plate
Now that you've removed the decorative rose plate, the interior rose plate (with screws) should exist exposed. Pick upward your Philips-caput screwdriver once more and loosen these screws.
Step 5: Unscrew the Confront Plate
Move on over to the faceplate at present and unscrew that. Once completed, remove the latch altogether.
Step 6: Remove Remaining Doorknob
Finally, grab the remaining exterior doorknob and pull.
Read more about the Best Type of Lock for Your Door.
Removing a Cylinder Door Lock
Cylinder locks are extremely common and this blazon of lock is still relatively unproblematic to remove. In just three quick steps, you can remove an existing cylinder lock for re-keying or replacement.
Tools Needed
To remove a cylinder lock, you lot'll demand just a few basic tools:
- Phillips-caput screwdriver
- Flat-caput screwdriver
- Allen wrench
Pace ane: Remove Screws
Start past using your Phillips-caput screwdriver to remove any visible screws from the interior side of the door. These are the screws that hold the lock and the door together.
Footstep two: Remove the Spindle
Next, you'll need to use your flat-head screwdriver to turn the spindle of the lock counter-clockwise around until it stops. This should be done by inserting the flat-head screwdriver (you may need to endeavor a few unlike sizes) into the lock itself.
Once the spindle stops turning, you should observe that the square tab within the spindle is perfectly aligned with the rest of the lock. At this point, you should be able to apply your flat-head screwdriver to carefully push on the tab that's belongings the spindle into place. When you do this, the spindle itself will pop out of its housing.
Footstep 3: Take the Cylinder Out
With the spindle gone, you'll now have access to the housing of the lock. Look advisedly inside the housing (a flashlight might be helpful here) until you locate some other small tab. Use your apartment-head screwdriver to push button downwardly on this tab, which will release the cylinder. However, in that location's a good run a risk that yous'll demand to employ an Allen wrench to push on the cylinder until it slides or pops out.
As you work on removing the cylinder, exist careful non to printing too hard with the screwdriver on the tab, as this can cause permanent harm to the betoken that the lock volition no longer exist usable.
Removing a Mortise Lock
Mortise locks take a pocket (called a mortise) that is cutting into the door itself. The lock is encased in this pocket, making it a more than secure locking method.
Tools Needed
Removing a mortise lock requires:
- Phillips-head screwdriver
- Flat-head screwdriver
- A hammer may be needed
Pace 1: Locate & Unscrew the Gear up Screw
This screw will exist on the shank of the within knob (the one you lot utilize to lock the door).
Footstep 2: Unscrew the Door Handles
The two door handles are screwed into each other through the spindle. Exist certain to unscrew them; do not just pull.
Step 3: Remove the Rose Plates
Unscrew the external doorknob rose plate that remains on the door using a Philips-head screwdriver.
Step 4: Remove the Face Plate
Unscrew the top and bottom screws located on the faceplate of the mortise lock using a Phillips-head screwdriver.
Step 5: Remove the Mortise Lock
Using your easily or plyers, take hold of the latch bolt and brainstorm to pull the mortise lock out. It should come out after a few, good pulls.
If the mortise lock can't exist hands removed, catch a large flat-head screwdriver and use that to pry it out. Insert the screwdriver into the hole where the spindle was. The screwdriver should fit snuggly in the hole. With your screwdriver perpendicular to the door, take a hammer and tap it in the direction of the strike place a few times.
In that location y'all have it: a few simple steps to removing a knob door lock, a cylinder door lock, and a mortise lock at your home. This is a bones DIY skill that any homeowner will benefit from knowing, especially if you e'er need to replace a lock or accept it re-keyed.
Get more expert advice: How to Repair Electronic Locks.
Residential Locksmith Services
Of class, if yous come across any troubles while trying to remove a lock at your home, feel complimentary to contact Groovy Valley Lockshop at 484-324-2986 or fill up out a service request for assistance.
Editor's Note: This post was originally published in February 2022 and has been completely updated for accuracy and comprehensiveness.
How To Remove Mortise Lock,
Source: https://www.gvlock.com/blog/how-to-remove-a-door-lock-at-home/
Posted by: moralesclacers.blogspot.com
0 Response to "How To Remove Mortise Lock"
Post a Comment